How to Program a Citroen Berlingo Key Fob

A key fob, or small device, alerts the vehicle that it's time to start or lock. These devices are powered with batteries. Unfortunately, sometimes these batteries die or get damaged. Fortunately, it's simple to replace these batteries.

There are many reasons that your key fob may not work. Some of these issues are easy to fix, while others require the assistance of a professional.

Battery

We believed that the battery was about to die when we noticed that the keyfob for the Berlingo no longer worked. The unlock button worked, so it was not a battery issue. Timpsons and Halfords claimed that the only way to replace a Berlingo keyfob's battery is to have a dealer handle it. This is because removing or replacing batteries within less than 30 seconds can cause the fob's memory to go away and you will be left with the key.

Press and HOLD the large plip switch with all doors closed, and the ignition turned ON. Press the small deadlock while holding the large button. This will set the Plip Key to your vehicle's default "lock" code.

Receiver module

A key fob is a tiny device that allows you to lock and unlock your vehicle from the distance. It communicates via radio frequency with the module receiver of the vehicle. If your key fob does not work, it could be due to a dead battery or a damaged receiver. It could also be caused by interference from other transmitters. This can be resolved by replacing the key fob's battery or reprogramming it. The procedure differs from one model to another, so you should consult the owner's manual of your specific car to learn how to do this.

A dead battery for a coin is the most common reason for keys not to work. This is an easy problem to fix. All you need to do is replace the battery with a fresh one of the same type and size. After that, press the start and lock buttons again to see if it works.

The sweat or moisture on the circuit board of your key fob may also lead to it not functioning properly. Moisture may cause a short-circuit, which could damage the receiver module. This would render your key fob useless. The best way to avoid this is to keep your key fob away from water and keep it in a dry place when not in use.

Other devices operating on the same frequency could interfere with your key fob. These devices include garage door openers home security systems, as well as cell phones. These devices may interfere with the signal coming from the citroen berlingo van key replacement keyfob, resulting the vehicle not being able to lock or start. Multimeters or similar tools can be used to test this.

If you're not able to fix the issue yourself then you should contact a locksmith for assistance. A professional locksmith can connect the key fob to your vehicle using specially designed equipment. This is much less expensive than buying new keys from dealers. But, you must contact a locksmith with experience in your brand of vehicle.

Interference

The key fob communicates with the vehicle via a specific frequency. If the fob is activated while it is within range of another transmitter it will lose signal and stop working properly. This can happen to cell phones, key fobs, or other devices operating on the same frequency. Key fobs may be malfunctioning due to the fact that the battery is not functioning properly. If this is the case it is possible to replace the key fob.

It is crucial to know that the receiver module is an essential component of the key fob, since it is responsible for transmitting the signal needed to open and start your vehicle. This component should be replaced in the event of a fault by a citroen replacement key fob Dealer or expert mechanic. A damaged receiver can cause keys to stop working. This isn't as frequent, however.

The battery might be dead if your key fob in your apartment isn't working. These small batteries, which look like coins, can be purchased in general stores as well in home improvement stores and auto parts shops. It is crucial to choose the correct type of battery, however. If the battery has the incorrect voltage, it could damage the chip inside the key fob.

A key fob submerged in water can lose its signal. In this situation it is recommended to remove the key fob as quickly as you can from the puddle. Then, you should clean the circuit board using a cotton swab that has been immersed in electronic cleaner or isopropyl. This will keep the circuit boards clean and prevent corrosion.

It's also possible that the key fob isn't properly programmed to the vehicle. If this is the case, it's recommended to visit the local citroen key dealership with your V5 registration and identity proof. Dealers can get the code for your car's immobiliser and order an alternative key fob for you. They can also program the replacement keyfob, and program the immobiliser to accept it.

Deprogramming

My Berlingo's lock button was not working for me recently. It worked fine for a time, but it then didn't respond to the key fob. The unlock button was still working though. I checked with Timpsons and Halfords who both advised that you can only deprogram the key fob by taking it to a dealer and trying anything else WILL RESULT in DOOM.

I then took out the negative cable and waited around 20 minutes to ensure the remaining power was completely drained. I then tried to reprogramme my key fob. I first had to make sure that all doors were locked with the key, and then I had to press and hold the large button for approximately 20 minutes. After pressing the large button, I let it go and then press the small button to secure the door. The LED now flashes continuously.

I then put in the ignition key and turned it into accessory position without turning off the engine. Then, I placed the Plip key toward the receiver at the front of the vehicle. I press the large plip switch followed by the smaller plip button on the remote. The Plip is now working. This should work if the key fob isn't responding to the remote.